Guangdong Crown Paint Company Limited

Super Wear-Resistant Polyurethane Floor Paint

  • main raw material: Polyurethane Resin
  • Suitable for factory,Shopping Mall,Garages,Hotel,Commercial Plaza,Showroom,etc.
  • Usage: indoor floor coating decoration protection waterproofing
  • Application tool: roller,spray
  • State: Liquid Coating
BASIC INFO
CP-808 is a three-component polyurethane floor paint,including paint,hardener,abrasive aggregate. Nice appearance, dust &corrosion resistant and easy to clean. The whole coating system can bond well with the solid base and has good abrasion and wearing resistance. Meanwhile, it is resistant to compression and impact and can stand heavy-duty load to a certain extent.

Advantages:

1. Abrasion resistance is 5-8 times of epoxy paint
2. aggregate improves hardness and abrasion,anti-slip largely
3. Yellowing UV Resistant is 28 times of Epoxy paint
4. Resistant to hot water flushing,chemical corrosion
5. Matt finish, Environmental Friendly.
6. Service Life: 10-20 Years

Where to Use:

It is mainly used for concrete surface where has compression & wearing resistance and anti-dust and corrosion requirement, such as industry workshop, office, warehouse, foodstuff factory etc.

Requirements on the Concrete Floor Substrate:

1. Concrete strength≥C25;
2. Flatness: the maximum altitude difference of 2M running rule锛3mm. 
3. The moisture content of the base锛4%

Technical Data:

Drying time:
Touch dry: 6 hours (25鈩)                   Hard dry: 7 days (25鈩)
Compressive strength (Mpa): ≥85
Impact resistance strength (Kg•cm): ≥50 
Tensile strength (Mpa): ≥7
James Friction Coefficient: 0.74-0.88
Pencil Hardness (H): ≥6H
Abrasion resistance(750g/1000r, zero gravity, g)≤0.002
Resistance to engine oil, diesel oil for 7 days: no change.
Resistance to 20% H2SO4 sulfuric acid for 7 days: no change
Resistance to 20% HNO3 for 7 days: no change
Resistance to 20% HCL for 7 days: no change
Resistance to 20% NaOH Sodium hydroxide for 7 days: no change
Resistance to 3% NaCL Sodium hydroxide for 7 days: no change
Resistance to 75% ethanol for 7 days: no change
Resistance to 75% Aliphatic Organic Solvent for 7 days: no change
Resistance to 75% Aromatic Organic Solvent for 7 days: no change
Resistance to Water for 7 days: no change

Recommended Consumption:


Models           Consumption
Topcoat (CP-808) 0.08-0.1 kg/sqm
Putty   (CP-MA) 0.2~0.3 kg/sqm
                    0.2~0.3 kg/sqm (Quartz Powder)
Undercoat (CP-MA) 0.4~0.6 kg/sqm
                          0.4~0.6kg/sqm (Quartz Sand)
Primer (CP-30) 0.15 kg/sqm

Clean up

Clean the application tools first with paper towels, then clean the tools with solvent before the paint hardens

Health and safety information

It contains certain chemicals which can cause skin irritation. Wear gloves, masks while handling the product, washing thoroughly after handling. Should skin contact occur, wash immediately with soap and water.
During application and curing in closed rooms, adequate fresh air ventilation must be provided. Keep away from open flames including welding.
In case of accidental eye contact, wash with a large quantity of water and immediately seek medical advice.
For detailed health, safety, environment recommendations, please consult and follow the instruction on the product material safety data sheet.


 
Previous 锛
Next锛